Öffnungszeiten: täglich 07–23 Uhr

TuningBot DTC-Datenbank · v4.40.3

P1325 Diagnose-Fehlercode (8 Interpretationen)

8 herstellerspezifische Interpretationen bei 7 Herstellern in der TuningBot DTC-Datenbank.

P · AntriebsstrangMotormanagementOBD2

Alfa Romeo

1 Interpretation
P1325
Engine control module (ECM), knock control - malfunction Alfa Romeo · Motormanagement Datenzuverlässigkeit 62%

The control module detected improper operation of the Engine control module (ECM), knock control. This is the manufacturer-specific definition used by Alfa Romeo.

Hyundai

1 Interpretation
P1325
Glow Relay Abnormal Hyundai · Motormanagement Datenzuverlässigkeit 62%

The control module registered the fault condition described as "Glow Relay Abnormal". This is the manufacturer-specific definition used by Hyundai.

Lexus

1 Interpretation
P1325
Ignition control - cylinder No.6 - circuit malfunction Lexus · Motormanagement Datenzuverlässigkeit 80%

The control module detected improper operation of the Ignition control - cylinder No.6 circuit. This is the manufacturer-specific definition used by Lexus.

Mögliche Ursachen

  • Wiring
  • ignition coil/module
  • ECM

Subaru

1 Interpretation
P1325
Knock sensor (KS) - voltage low Subaru · Zündung Datenzuverlässigkeit 80%

The control module detected that the Knock sensor (KS) voltage stayed below the expected range. This is the manufacturer-specific definition used by Subaru.

Mögliche Ursachen

  • Wiring
  • KS
  • ECM

Toyota

1 Interpretation
P1325
Ignition control - cylinder No. 6 - circuit malfunction Toyota · Motormanagement Datenzuverlässigkeit 62%

The control module detected improper operation of the Ignition control - cylinder No. 6 circuit. This is the manufacturer-specific definition used by Toyota.

Mögliche Ursachen

  • Wiring
  • ignition coil/module
  • ECM

VAG

2 Interpretationen
P1325
Knock control, cylinder 1 - control limit reached VAG · Motormanagement Datenzuverlässigkeit 62%

The control module detected that the monitored Knock control, cylinder 1 - control value reached its permissible limit. This is the manufacturer-specific definition used by Audi.

Mögliche Ursachen

  • Poor quality fuel
  • incorrect fuel
  • insecure engine component
  • KS incorrectly tightened/ defec tive
  • shield wiring open circuit
  • poor connection
Gilt für Audi
P1325
Knock control, cylinder 1 - control limit reached VAG · Motormanagement Datenzuverlässigkeit 80%

The control module detected that the monitored Knock control, cylinder 1 - control value reached its permissible limit. This is the manufacturer-specific definition used by Volkswagen.

Mögliche Ursachen

  • Poor quality fuel
  • incorrect fuel
  • insecure engine component
  • KS incorrectly tightened/ defec tive
  • shield wiring open circuit
  • poor connection
Gilt für Volkswagen

Volvo

1 Interpretation
P1325
Engine control module (ECM), knock control detection - circuit test pulse Volvo · Motormanagement Datenzuverlässigkeit 62%

The control module detected a fault associated with the Engine control module (ECM), knock control detection - circuit test pulse circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Volvo.

Mögliche Ursachen

ECM

Verwandte und benachbarte Codes

So liest man P1325

P

Antriebsstrang: Motor, Getriebe und Antrieb.

1

Herstellerdefinierter Bereich: die Bedeutung kann je Marke abweichen.

325

Spezifischer Fehlerindex innerhalb des Subsystems.

Häufige Fragen zu P1325

Was bedeutet P1325?

Diagnose-Fehlercode (8 Interpretationen). The control module detected improper operation of the Engine control module (ECM), knock control. This is the manufacturer-specific definition used by Alfa Romeo.

Ist P1325 generisch oder herstellerspezifisch?

P1325 ist ein herstellerspezifischer Code. In dieser Datenbank ist er dokumentiert für: Alfa Romeo, Hyundai, Lexus, Subaru, Toyota, VAG, Volvo. Dieselbe Nummer kann bei anderen Marken etwas anderes bedeuten.

Kann TuningBot P1325 auf Dateiebene entfernen?

Wenn die Fehlerlogik in der Steuergerätekalibrierung liegt, ja: unser DTC-Removal-Dienst deaktiviert den konkreten Fehlereintrag. Die Checksum-Korrektur ist nicht enthalten: Sie ist ein separater, optionaler Service. Unsicher, ob Ihr Fall dazugehört? Fordern Sie eine kostenlose Einschätzung an, und unsere Ingenieure prüfen Ihre Datei.

Weitere Dateidienste

ChiptuningPrüfstandsergebnisse nach Modell und Motor Ergebnisse ansehen →

← Die gesamte DTC-Datenbank durchsuchen