Öffnungszeiten: täglich 07–23 Uhr

TuningBot DTC-Datenbank · v4.40.3

P1198 Diagnose-Fehlercode (8 Interpretationen)

8 herstellerspezifische Interpretationen bei 7 Herstellern in der TuningBot DTC-Datenbank.

P · AntriebsstrangMotormanagementOBD2

BMW

1 Interpretation
P1198
Mass air flow (MAF)/vane air flow (VAF) - flow too high BMW · Motormanagement Datenzuverlässigkeit 62%

The control module detected that the Mass air flow (MAF)/vane air flow (VAF) - flow value was above the expected limit. This is the manufacturer-specific definition used by BMW.

Mögliche Ursachen

  • Wiring
  • MAF/VAF sensor
  • vacuum leaks

Chrysler

1 Interpretation
P1198
Radiator Temp Sensor Input Too High Chrysler · Thermomanagement Datenzuverlässigkeit 62%

The control module detected that the Radiator Temp Sensor Input value was above the expected limit. This is the manufacturer-specific definition used by Chrysler.

Ford

1 Interpretation
P1198
Pump Rotor Control Underfueling Ford · Motormanagement Datenzuverlässigkeit 80%

The control module detected a fault associated with the Pump Rotor Control Underfueling circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Ford.

Jeep

1 Interpretation
P1198
Radiator Temperature Sensor Voltage Too High Jeep · Thermomanagement Datenzuverlässigkeit 62%

The control module detected that the Radiator Temperature Sensor Voltage value was above the expected limit. This is the manufacturer-specific definition used by Jeep.

Empfohlene Prüfungen

  • Perform a full module scan
  • Review freeze-frame and occurrence data
  • Confirm the exact vehicle, ECU and software context
  • Inspect relevant wiring and connectors
  • Check applicable OEM service information

MINI

1 Interpretation
P1198
Differential Pressure Sensor Intake Manifold Signal MINI · Abgas Datenzuverlässigkeit 62%

The control module detected a fault associated with the Differential Pressure Sensor Intake Manifold Signal circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by MINI.

PSA

1 Interpretation
P1198
Fuel flow regulation electrovalve : Flow too low PSA · Kraftstoffsystem Datenzuverlässigkeit 72%

The control module detected that the Fuel flow regulation electrovalve was below its expected limit. Documented for the Siemens SID 803 injection ECU (DW10BTED4 2.0 HDi) on Peugeot applications; the same PSA control units are also fitted to Citroën models.

Gilt für Peugeot Siemens SID 803 injection ECU (DW10BTED4 2.0 HDi)

VAG

2 Interpretationen
P1198
Heated oxygen sensor (HO2S) 2, Bank 1, heater circuit malfunction VAG · Abgas Datenzuverlässigkeit 62%

The control module detected improper operation of the Heated oxygen sensor (HO2S) 2, Bank 1, heater circuit. This is the manufacturer-specific definition used by Audi.

Mögliche Ursachen

  • Wiring
  • HO2S
Gilt für Audi
P1198
Heated oxygen sensor (HO2S) heater circuit malfunction VAG · Abgas Datenzuverlässigkeit 80%

The control module detected improper operation of the Heated oxygen sensor (HO2S) heater circuit. This is the manufacturer-specific definition used by Volkswagen.

Mögliche Ursachen

  • Wiring
  • HO2S
Gilt für Volkswagen

Verwandte und benachbarte Codes

So liest man P1198

P

Antriebsstrang: Motor, Getriebe und Antrieb.

1

Herstellerdefinierter Bereich: die Bedeutung kann je Marke abweichen.

198

Spezifischer Fehlerindex innerhalb des Subsystems.

Häufige Fragen zu P1198

Was bedeutet P1198?

Diagnose-Fehlercode (8 Interpretationen). The control module detected that the Mass air flow (MAF)/vane air flow (VAF) - flow value was above the expected limit. This is the manufacturer-specific definition used by BMW.

Ist P1198 generisch oder herstellerspezifisch?

P1198 ist ein herstellerspezifischer Code. In dieser Datenbank ist er dokumentiert für: BMW, Chrysler, Ford, Jeep, MINI, PSA, VAG. Dieselbe Nummer kann bei anderen Marken etwas anderes bedeuten.

Kann TuningBot P1198 auf Dateiebene entfernen?

Wenn die Fehlerlogik in der Steuergerätekalibrierung liegt, ja: unser DTC-Removal-Dienst deaktiviert den konkreten Fehlereintrag. Die Checksum-Korrektur ist nicht enthalten: Sie ist ein separater, optionaler Service. Unsicher, ob Ihr Fall dazugehört? Fordern Sie eine kostenlose Einschätzung an, und unsere Ingenieure prüfen Ihre Datei.

Weitere Dateidienste

ChiptuningPrüfstandsergebnisse nach Modell und Motor Ergebnisse ansehen →

← Die gesamte DTC-Datenbank durchsuchen