The control module detected a fault associated with the Secondary Air System Bank 2 circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by BMW.
TuningBot DTC-Datenbank · v4.41.2
P1197 Diagnose-Fehlercode (11 Interpretationen)
11 herstellerspezifische Interpretationen bei 9 Herstellern in der TuningBot DTC-Datenbank.
BMW
1 Interpretation
Chrysler
1 InterpretationThe control module detected that the Heated oxygen sensor (HO2S) 2, bank 1 responded more slowly than expected. This is the manufacturer-specific definition used by Chrysler.
Mögliche Ursachen
- Wiring
- heating inoperative
- HO2S
Ford
1 InterpretationThe control module detected that the Key Off voltage stayed below the expected range. This is the manufacturer-specific definition used by Ford.
Jeep
1 InterpretationThe control module detected that the Heated oxygen sensor (HO2S) 2, bank 1 responded more slowly than expected. This is the manufacturer-specific definition used by Jeep.
Mögliche Ursachen
- Wiring
- heating inoperative
- exhaust leak
- HO2S
Mazda
1 InterpretationThe control module detected improper operation of the Mileage Switch circuit. This is the manufacturer-specific definition used by Mazda.
MINI
1 InterpretationThe control module detected a fault associated with the Differential Pressure Sensor Intake Manifold Signal circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by MINI.
Nissan
1 InterpretationThe control module detected that the Low Input From Fuel Level Sensor signal stayed below the expected range. This is the manufacturer-specific definition used by Nissan.
PSA
2 InterpretationenThe control module detected the fault condition "ECU internal fault" for the Injectors control. Documented for the Bosch EDC16C34 injection ECU (DV6TED4 1.6 HDi) on Peugeot applications; the same PSA control units are also fitted to Citroën models.
The control module detected the fault condition "Harness, injector, ECU power stage" for the Injectors control. Documented for the Siemens SID 803 injection ECU (DW10BTED4 2.0 HDi) on Peugeot applications; the same PSA control units are also fitted to Citroën models.
VAG
2 InterpretationenThe control module detected improper operation of the Heated oxygen sensor (HO2S) 1, Bank 2, heater circuit. This is the manufacturer-specific definition used by Audi.
Mögliche Ursachen
- Wiring
- HO2S
The control module detected improper operation of the Heated oxygen sensor (HO2S) heater circuit. This is the manufacturer-specific definition used by Volkswagen.
Mögliche Ursachen
- Wiring
- HO2S
Verwandte und benachbarte Codes
So liest man P1197
Antriebsstrang: Motor, Getriebe und Antrieb.
Herstellerdefinierter Bereich: die Bedeutung kann je Marke abweichen.
Spezifischer Fehlerindex innerhalb des Subsystems.
Häufige Fragen zu P1197
Was bedeutet P1197?
Diagnose-Fehlercode (11 Interpretationen). The control module detected a fault associated with the Secondary Air System Bank 2 circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by BMW.
Ist P1197 generisch oder herstellerspezifisch?
P1197 ist ein herstellerspezifischer Code. In dieser Datenbank ist er dokumentiert für: BMW, Chrysler, Ford, Jeep, Mazda, MINI, Nissan, PSA, VAG. Dieselbe Nummer kann bei anderen Marken etwas anderes bedeuten.
Kann TuningBot P1197 auf Dateiebene entfernen?
Wenn die Fehlerlogik in der Steuergerätekalibrierung liegt, ja: unser DTC-Removal-Dienst deaktiviert den konkreten Fehlereintrag. Die Checksum-Korrektur ist nicht enthalten: Sie ist ein separater, optionaler Service. Unsicher, ob Ihr Fall dazugehört? Fordern Sie eine kostenlose Einschätzung an, und unsere Ingenieure prüfen Ihre Datei.
Weitere Dateidienste
Das System hinter diesem Code verstehen: Sekundärluftsystem
