TuningBot DTC Database · v4.37.14
11 manufacturer-specific interpretations across 7 manufacturers in the TuningBot DTC database.
ChevroletThe control module detected a fault associated with the Ignition Control Cylinder 7 Not Toggling After Enable circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Chevrolet.
ChryslerThe control module detected a fault associated with the IC Cylinder 7 Not Toggling After Enable circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Chrysler.
Land RoverThe control module detected improper operation of the Ignition system circuit. This is the manufacturer-specific definition used by Land Rover.
LexusThe control module detected improper operation of the Camshaft position (CMP) actuator, bank 2, circuit E circuit. This is the manufacturer-specific definition used by Lexus.
PSAThe control module detected that the Control of injector for cylinder n°2 was below its expected limit. Documented for the Bosch EDC16C34 injection ECU (DV6TED4 1.6 HDi) on Peugeot applications; the same PSA control units are also fitted to Citroën models.
The control module detected the fault condition "Electrical specifications outside the norms (harness or injector)" for the Injector 2 control. Documented for the Continental SID 807 injection ECU (DV6C 1.6 HDi) on Peugeot applications; the same PSA control units are also fitted to Citroën models.
The control module detected the fault condition "Electrical characteristics outside the standards (Harness or injector)" for the Injector 2 control. Documented for the Delphi DCM 3.5 injection ECU (DW10C 2.0 HDi) on Peugeot applications; the same PSA control units are also fitted to Citroën models.
The control module detected that the Control of injector for cylinder n°2 was below its expected limit. Documented for the Siemens SID 803 injection ECU (DW10BTED4 2.0 HDi) on Peugeot applications; the same PSA control units are also fitted to Citroën models.
ToyotaThe control module detected an interruption (open circuit) in the 'E' Camshaft Position Actuator circuit, so the expected electrical continuity was not present. This is the manufacturer-specific definition used by Toyota.
VAGThe control module detected an interruption (open circuit) in the Ignition coil/amplifier, cylinder 5 circuit, so the expected electrical continuity was not present. This is the manufacturer-specific definition used by Audi.
The control module detected an interruption (open circuit) in the Ignition coil/amplifier, cylinder 5 circuit, so the expected electrical continuity was not present. This is the manufacturer-specific definition used by Volkswagen.
Powertrain: engine, transmission and driveline systems.
Manufacturer-defined range: the meaning can differ between brands.
Specific fault index within the subsystem.
Diagnostic Trouble Code (11 interpretations). The control module detected a fault associated with the Ignition Control Cylinder 7 Not Toggling After Enable circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Chevrolet.
P1367 is a manufacturer-specific code. In this database it is documented for: Chevrolet, Chrysler, Land Rover, Lexus, PSA, Toyota, VAG. The same number can mean something different on other brands.
If the fault logic lives in the ECU calibration, yes: our DTC Removal file service disables the specific fault entry and, where the ECU needs it, corrects the checksum too. Not sure whether your case qualifies? Request a free assessment and our engineers will check your ECU file.
Understand the system behind this code: Diagnostic Strategy and DTC Logic
ItalianoIT
DeutschDE
EspañolES
PortuguêsPT
FrançaisFR
РусскийRU