The control module detected a condition consistent with a leak affecting the Leakage Diagnostic Pump Control. This is the manufacturer-specific definition used by BMW.
TuningBot DTC-Datenbank · v4.40.3
P1230 Diagnose-Fehlercode (11 Interpretationen)
11 herstellerspezifische Interpretationen bei 10 Herstellern in der TuningBot DTC-Datenbank.
BMW
1 Interpretation
Hyundai
1 InterpretationThe control module detected a fault associated with the Slow Duty Solenoid circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Hyundai.
Jaguar
1 InterpretationThe control module detected a fault associated with the Fuel Pump Relay circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Jaguar.
Land Rover
1 InterpretationThe control module detected an interruption (open circuit) in the Fuel pump (FP) relay circuit, so the expected electrical continuity was not present. This is the manufacturer-specific definition used by Land Rover.
Mögliche Ursachen
- Wiring
- FP relay
MINI
1 InterpretationThe control module detected a fault associated with the Fuel Pump Relay Activation circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by MINI.
Opel
1 InterpretationThe control module detected that the Engine control relay voltage stayed below the expected range. This is the manufacturer-specific definition used by Opel.
Porsche
1 InterpretationThe control module detected a fault associated with the Fuel Injector Cylinder 6 circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by Porsche.
Subaru
1 InterpretationThe control module detected improper operation of the Fuel pump (FP) control module circuit. This is the manufacturer-specific definition used by Subaru.
Mögliche Ursachen
- Wiring
- FP control module
- ECM
VAG
2 InterpretationenThe control module detected a short circuit to ground in the Injector 6 circuit. This is the manufacturer-specific definition used by Audi.
Mögliche Ursachen
- Wiring short to ground
- injector
The control module detected a short circuit to ground in the Injector 6 circuit. This is the manufacturer-specific definition used by Volkswagen.
Mögliche Ursachen
- Wiring short to ground
- injector
Volvo
1 InterpretationThe control module detected that the Mass air flow (MAF) signal stayed below the expected range. This is the manufacturer-specific definition used by Volvo.
Mögliche Ursachen
- Wiring
- short to ground
- MAF sensor
- ECM
Verwandte und benachbarte Codes
So liest man P1230
Antriebsstrang: Motor, Getriebe und Antrieb.
Herstellerdefinierter Bereich: die Bedeutung kann je Marke abweichen.
Spezifischer Fehlerindex innerhalb des Subsystems.
Häufige Fragen zu P1230
Was bedeutet P1230?
Diagnose-Fehlercode (11 Interpretationen). The control module detected a condition consistent with a leak affecting the Leakage Diagnostic Pump Control. This is the manufacturer-specific definition used by BMW.
Ist P1230 generisch oder herstellerspezifisch?
P1230 ist ein herstellerspezifischer Code. In dieser Datenbank ist er dokumentiert für: BMW, Hyundai, Jaguar, Land Rover, MINI, Opel, Porsche, Subaru, VAG, Volvo. Dieselbe Nummer kann bei anderen Marken etwas anderes bedeuten.
Kann TuningBot P1230 auf Dateiebene entfernen?
Wenn die Fehlerlogik in der Steuergerätekalibrierung liegt, ja: unser DTC-Removal-Dienst deaktiviert den konkreten Fehlereintrag. Die Checksum-Korrektur ist nicht enthalten: Sie ist ein separater, optionaler Service. Unsicher, ob Ihr Fall dazugehört? Fordern Sie eine kostenlose Einschätzung an, und unsere Ingenieure prüfen Ihre Datei.
Weitere Dateidienste
Das System hinter diesem Code verstehen: MAF-Sensor
