The control module detected a fault associated with the Battery Voltage circuit or function; the stored code identifies the affected component rather than a single failure mode.
Base de données DTC TuningBot · v4.37.15
U3003 Code défaut de diagnostic (3 variantes)
Interprétation générique (OBD-II) + 2 spécifiques au constructeur dans la base DTC TuningBot.
Interprétation générique (OBD-II)
Interprétations spécifiques au constructeur
Ford
3 interprétationsThe Ford Explorer PSCM detected battery voltage with failure type 16, circuit voltage below threshold. This interpretation is specific to the documented EPAS controller and model years.
Vérifications recommandées
- Perform a full module scan
- Verify battery voltage and PSCM power supplies
- Inspect EPAS wiring and connectors
- Review PSCM snapshot and extended data
- Follow the Ford EPAS diagnostic procedure
The Ford Explorer PSCM detected battery voltage with failure type 17, circuit voltage above threshold. This interpretation is specific to the documented EPAS controller and model years.
Vérifications recommandées
- Perform a full module scan
- Verify battery voltage and PSCM power supplies
- Inspect EPAS wiring and connectors
- Review PSCM snapshot and extended data
- Follow the Ford EPAS diagnostic procedure
The Ford Explorer PSCM detected battery voltage with failure type 68, event information. This interpretation is specific to the documented EPAS controller and model years.
Vérifications recommandées
- Perform a full module scan
- Verify battery voltage and PSCM power supplies
- Inspect EPAS wiring and connectors
- Review PSCM snapshot and extended data
- Follow the Ford EPAS diagnostic procedure
Land Rover
2 interprétationsThe L405 Deployable Side Step ECU detected battery voltage with failure type 16, circuit voltage below threshold. This interpretation is limited to the documented DSS controller.
Vérifications recommandées
- Perform a full module scan
- Verify battery voltage
- Inspect DSS wiring and connectors
- Inspect the running-board mechanism for binding
- Check the Hall-effect sensor signal when applicable
- Follow the Land Rover DSS troubleshooting guide
The L405 Deployable Side Step ECU detected battery voltage with failure type 17, circuit voltage above threshold. This interpretation is limited to the documented DSS controller.
Vérifications recommandées
- Perform a full module scan
- Verify battery voltage
- Inspect DSS wiring and connectors
- Inspect the running-board mechanism for binding
- Check the Hall-effect sensor signal when applicable
- Follow the Land Rover DSS troubleshooting guide
Codes liés et voisins
Comment lire U3003
Réseau : communication entre calculateurs.
Code générique standard SAE : même signification sur toutes les marques.
Index de défaut spécifique dans le sous-système.
Questions fréquentes sur U3003
Que signifie U3003 ?
Code défaut de diagnostic (3 variantes). The control module detected a fault associated with the Battery Voltage circuit or function; the stored code identifies the affected component rather than a single failure mode.
U3003 est-il générique ou spécifique au constructeur ?
U3003 existe à la fois comme code générique OBD-II (même signification sur toutes les marques) et avec 2 interprétations spécifiques au constructeur : Ford, Land Rover. À lire toujours dans le contexte de votre véhicule.
TuningBot peut-il supprimer U3003 au niveau du fichier ?
Non garanti. Les codes powertrain (P) se désactivent de façon fiable dans la calibration, mais les codes carrosserie, châssis et réseau dépendent du calculateur et de la façon dont le défaut est implémenté - certains sont traitables, d'autres non. Demandez un devis et nos ingénieurs examineront votre fichier et vous diront gratuitement si U3003 est supprimable dans votre cas.
Autres services fichier
Comprendre le système derrière ce code : Stratégie de diagnostic et logique DTC
