Блок управления обнаружил обрыв цепи «управление: насос B охлаждающей жидкости»: ожидаемая электрическая проводимость отсутствовала.
База данных DTC TuningBot · v4.41.2
P261A Диагностический код неисправности (вариантов: 9)
Общая (OBD-II) интерпретация + 1 специфичных для производителя в базе DTC TuningBot.
Общая (OBD-II) интерпретация
Интерпретации производителей
Ford
9 интерпретацийFord documents P261A:11 (circuit short to ground) for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “b” control circuit low. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Inspect relevant wiring and connectors
- Check power supplies and grounds
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:12 (circuit short to battery) for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “b” control circuit high. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Inspect relevant wiring and connectors
- Check power supplies and grounds
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:13 (circuit open) for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “b” control circuit/open. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Inspect relevant wiring and connectors
- Check power supplies and grounds
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:1C for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “a” control supply voltage out of range. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:71 for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “a” control actuator stuck. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:92 for its 2024-2025 gasoline-engine OBD monitor strategy as 1 – coolant pump “b” control performance/stuck off. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:98 for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “a” control system over temperature. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:B1 for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “a” control overspeed/dry run. This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Compare commanded and measured values
- Check applicable OEM service information
Ford documents P261A:B2 for its 2024-2025 gasoline-engine OBD monitor strategy as coolant pump “a” control under-speed "b" is defined as high temp loop aux pump - component cooling #1". This three-byte interpretation is application-specific and identifies the detected monitor condition rather than a confirmed failed component.
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Compare commanded and measured values
- Check applicable OEM service information
Связанные и соседние коды
Как читать P261A
Силовой агрегат: двигатель, коробка и трансмиссия.
Общий код стандарта SAE: одинаковое значение у всех марок.
Конкретный индекс неисправности внутри подсистемы.
Частые вопросы о P261A
Что означает P261A?
Диагностический код неисправности (вариантов: 9). Блок управления обнаружил обрыв цепи «управление: насос B охлаждающей жидкости»: ожидаемая электрическая проводимость отсутствовала.
P261A — общий код или специфичный для производителя?
P261A существует и как общий код OBD-II (одинаковое значение у всех марок), и с 1 интерпретациями производителей: Ford. Всегда читайте его в контексте вашего автомобиля.
Может ли TuningBot удалить P261A на уровне файла?
Если логика неисправности заложена в калибровке ЭБУ — да: наша услуга DTC Removal отключает конкретную запись ошибки. Коррекция checksum не входит в услугу: это отдельная опциональная услуга. Не уверены, подходит ли ваш случай? Запросите бесплатную оценку, и наши инженеры проверят ваш файл.
Другие услуги по файлу
Разобраться в системе за этим кодом: Диагностическая стратегия и логика DTC
