The control module detected an interruption (open circuit) in the Diagnostic Module Tank Leakage Pump Control circuit, so the expected electrical continuity was not present. This is the manufacturer-specific definition used by BMW.
База данных DTC TuningBot · v4.41.2
P1236 Диагностический код неисправности (интерпретаций: 11)
В базе DTC TuningBot — интерпретаций производителей: 11; марок: 11.
BMW
1 интерпретация
Chevrolet
1 интерпретацияThe control module detected improper operation of the Injector 5 circuit. This is the manufacturer-specific definition used by Chevrolet.
Возможные причины
- Wiring
- injector
- ECM
Ford
1 интерпретацияThe control module detected that the Fuel Pump Control value was outside the valid range. This is the manufacturer-specific definition used by Ford.
Возможные причины
- Wiring
- fuel pump
- fuel pump control module
- ECM
Рекомендуемые проверки
- Perform a full module scan
- Review freeze-frame and occurrence data
- Compare commanded and measured values
- Check applicable OEM service information
Hyundai
1 интерпретацияThe control module detected that the Active Air Flap F/B voltage stayed below the expected range. This is the manufacturer-specific definition used by Hyundai.
Jaguar
1 интерпретацияThe control module detected improper operation of the VSV 1 circuit. This is the manufacturer-specific definition used by Jaguar.
Lexus
1 интерпретацияThe control module detected improper operation of the Fuel high - pressure pump, bank 2 circuit. This is the manufacturer-specific definition used by Lexus.
Возможные причины
- Wiring
- fuel high - pressure pump
- injector control module
- bank 2
Mercedes-Benz
1 интерпретацияThe control module detected improper operation of the Supercharger (SC) clutch. This is the manufacturer-specific definition used by Mercedes-Benz.
Возможные причины
- Wiring
- SC clutch
- ECM
MINI
1 интерпретацияThe control module detected a fault associated with the Fuel Pump Relay Activation circuit or function; the stored code identifies the affected component rather than a single failure mode. This is the manufacturer-specific definition used by MINI.
Mitsubishi
1 интерпретацияThe control module detected improper operation of the Accelerator pedal position (APP) sensor B. This is the manufacturer-specific definition used by Mitsubishi.
Возможные причины
- Wiring
- ECM
Nissan
1 интерпретацияThe control module detected improper operation of the Throttle control motor - short circuit. This is the manufacturer-specific definition used by Nissan.
Возможные причины
- Wiring
- throttle control motor
Toyota
1 интерпретацияThe control module detected improper operation of the High Pressure Fuel Pump Number 2 circuit. This is the manufacturer-specific definition used by Toyota.
Связанные и соседние коды
Как читать P1236
Силовой агрегат: двигатель, коробка и трансмиссия.
Диапазон, заданный производителем: значение может отличаться у разных марок.
Конкретный индекс неисправности внутри подсистемы.
Частые вопросы о P1236
Что означает P1236?
Диагностический код неисправности (интерпретаций: 11). The control module detected an interruption (open circuit) in the Diagnostic Module Tank Leakage Pump Control circuit, so the expected electrical continuity was not present. This is the manufacturer-specific definition used by BMW.
P1236 — общий код или специфичный для производителя?
P1236 — код конкретного производителя. В этой базе он описан для: BMW, Chevrolet, Ford, Hyundai, Jaguar, Lexus, Mercedes-Benz, MINI, Mitsubishi, Nissan, Toyota. Тот же номер у других марок может означать другое.
Может ли TuningBot удалить P1236 на уровне файла?
Если логика неисправности заложена в калибровке ЭБУ — да: наша услуга DTC Removal отключает конкретную запись ошибки. Коррекция checksum не входит в услугу: это отдельная опциональная услуга. Не уверены, подходит ли ваш случай? Запросите бесплатную оценку, и наши инженеры проверят ваш файл.
Другие услуги по файлу
Разобраться в системе за этим кодом: Диагностическая стратегия и логика DTC
