ItalianoIT
DeutschDE
EspañolES
PortuguêsPT
FrançaisFR
РусскийRU
Fiat-Alfa-Lancia 2.0 JTDM Remap & Chiptuning – Alfa Giulietta, 159, Fiat Bravo
Professional ECU tuning and remapping for the Fiat-Alfa-Lancia 2.0 JTDM diesel engine. Our dyno-tested Stage 1 calibrations improve torque delivery, throttle response and drivability, with optional DPF, EGR and AdBlue/SCR solutions for supported ECUs.
Engine codes: 2.0 JTDm
Fitted to Alfa Giulietta159Fiat Bravo
Performance Gains (Dyno-Tested)
| Engine | Stock | Tuned | HP Gain | Torque Gain | ECU | Order |
|---|---|---|---|---|---|---|
| 2.0 JTDM | 170 hp | 202 hp | +32 hp +19% | +68 Nm | EDC16C39Stage 1 | Order file → |
Figures are dyno-tested averages and may vary with hardware condition and fuel quality.
Cars this engine is fitted to
Alfa Romeo Giulietta, 159, Fiat Bravo, Lancia Delta, Saab 9-3, Alfa Romeo 147 and 4 more across Alfa, Fiat, Lancia and Saab
Fitment is read from the ECU part numbers in our own database, not from a generic catalogue. The same engine and control unit are fitted to several cars, which is why one page serves them all.Measured here, tunable everywhere
The figures in the table above are readings taken on the dyno for this engine, not software estimates rounded up to sell a file, and our Stage 1 is calibrated to stay inside the margins the engine was designed with. Only a part of our work is published this way: every ECU, engine and model we can read can be remapped for power, measured page or not.
Available ECU Services for this Engine
The following solutions are supported on the ECU(s) of this vehicle (Diesel):
Technical Notes per ECU
Disconnection and read requirements differ by ECU. The notes below apply to the specific ECU listed; the exact removal scope per service is confirmed on each service page.
Each note is tagged with the service it refers to and applies to the ECU it is listed under. Mechanical preparation is the installer's responsibility. Emission-related solutions are for off-road or motorsport use where permitted by law.
Supported ECU(s): EDC16C39
Frequently Asked Questions
How much power can a Fiat-Alfa-Lancia 2.0 JTDM gain with Stage 1 tuning?
Stage 1 ECU tuning for the Fiat-Alfa-Lancia 2.0 JTDM can add up to +32 hp and +68 Nm of torque, based on dyno-tested calibrations. Actual figures depend on the exact engine variant and hardware condition.
Can DPF and EGR be removed on the Fiat-Alfa-Lancia 2.0 JTDM?
DPF and EGR off is supported on the ECU(s) of this vehicle, strictly for off-road or motorsport use where permitted by law. The exact mechanical preparation and sensor handling are listed per ECU in the technical notes below.
How do I order and how fast is the tuning file delivered?
Upload your original ECU read through the tuning page and receive the calibration by email. Most files are delivered within 15-20 minutes during working hours (daily, 07:00-23:00 CET).
Is the Fiat-Alfa-Lancia 2.0 JTDM tuning file plug-and-play?
You receive a ready-to-flash calibration based on your original file. Flashing it back to the ECU and any related mechanical preparation are handled by the installer with their own tools.
Order your Fiat-Alfa-Lancia 2.0 JTDM tuning file
Upload your original ECU file and receive a professional calibration in 15-20 minutes.
Tune Your File →v4.31.23