Mini 2.0 TURBO Remap & Chiptuning – JCW GP F56, JCW Clubman F54, JCW Countryman F60

Professional ECU tuning and remapping for the Mini 2.0 TURBO petrol engine. Our dyno-tested Stage 1 and Stage 2 calibrations sharpen throttle response and power delivery, with options such as Pop & Bang, GPF/OPF off and limiter changes for supported ECUs.

Engine codes: B48A20 306 hp

Fitted to JCW GP F56JCW Clubman F54JCW Countryman F60

+37 hp Best Stage 1 power gain

+79 Nm Best Stage 1 torque gain

1 ECU variant covered

Petrol Fuel type

Performance Gains (Dyno-Tested)

Engine	Stock	Tuned	HP Gain	Torque Gain	ECU	Order
2.0 TURBO	231 hp	258 hp	+27 hp +12%	+67 Nm	MG1CS201Stage 1	Order file →
2.0 TURBO	192 hp	229 hp	+37 hp +19%	+79 Nm	MG1CS201Stage 1	Order file →

Figures are dyno-tested averages and may vary with hardware condition and fuel quality.

Cars this engine is fitted to

JCW GP F56, Mini Cooper, JCW Clubman F54, Mini Cooper Clubman, JCW Countryman F60, Mini Cooper S and 2 more

Mini · 8

CooperCooper ClubmanCooper SCooper S ClubmanJCW Clubman F54JCW Countryman F60JCW GP F56John Cooper Works

Fitment is read from the ECU part numbers in our own database, not from a generic catalogue. The same engine and control unit are fitted to several cars, which is why one page serves them all.

Measured here, tunable everywhere

The figures in the table above are readings taken on the dyno for this engine, not software estimates rounded up to sell a file, and our Stage 1 is calibrated to stay inside the margins the engine was designed with. Only a part of our work is published this way: every ECU, engine and model we can read can be remapped for power, measured page or not.

Available ECU Services for this Engine

The following solutions are supported on the ECU(s) of this vehicle (Petrol):

Cold Start Noise Reduction DTC Removal EVAP Removal GPF/OPF Lambda Pop&Bang Readiness Calibration Sport Displays Calibration

Technical Notes per ECU

Disconnection and read requirements differ by ECU. The notes below apply to the specific ECU listed; the exact removal scope per service is confirmed on each service page.

MG1CS201

Lambda/O2 off PROBE MUST BE DISCONNECTED

Each note is tagged with the service it refers to and applies to the ECU it is listed under. Mechanical preparation is the installer's responsibility. Emission-related solutions are for off-road or motorsport use where permitted by law.

Supported ECU(s): MG1CS201

Frequently Asked Questions

How much power can a Mini 2.0 TURBO gain with Stage 1 tuning?

Stage 1 ECU tuning for the Mini 2.0 TURBO can add up to +37 hp and +79 Nm of torque, based on dyno-tested calibrations. Actual figures depend on the exact engine variant and hardware condition.

Can GPF/OPF be removed on the Mini 2.0 TURBO?

GPF/OPF off is supported on the ECU(s) of this vehicle, strictly for off-road or motorsport use where permitted by law. The exact mechanical preparation and sensor handling are listed per ECU in the technical notes below.

How do I order and how fast is the tuning file delivered?

Upload your original ECU read through the tuning page and receive the calibration by email. Most files are delivered within 15-20 minutes during working hours (daily, 07:00-23:00 CET).

Is the Mini 2.0 TURBO tuning file plug-and-play?

You receive a ready-to-flash calibration based on your original file. Flashing it back to the ECU and any related mechanical preparation are handled by the installer with their own tools.

Order your Mini 2.0 TURBO tuning file

Upload your original ECU file and receive a professional calibration in 15-20 minutes.

Tune Your File →

← See all dyno results

v4.31.23