ItalianoIT
DeutschDE
EspañolES
PortuguêsPT
FrançaisFR
РусскийRU
Ford Puma ECU Tuning: Stage 1 Gains by Engine
Dyno-tested Stage 1 results for every Ford Puma engine we have on the bench. Pick your engine for the full page with ECUs, notes and services, or upload your file straight away.
Generations covered: Puma ST
Stage 1 gains by engine
Best Stage 1 result per engine family on the power variants this model carries; the table below lists the versions matched exactly.
| Engine | Stock | HP Gain | Torque Gain | Details |
|---|---|---|---|---|
| 1.0 ECOBOOST BPF petrol | 95–125 hp | from +11 to +21 hp | +63 Nm | Engine page → |
| 1.5 ECOBOOST petrol | 120–200 hp | from +21 to +63 hp | +58 Nm | Engine page → |
| 1.5 TDCI diesel | 75–120 hp | from +19 to +26 hp | +55 Nm | Engine page → |
Figures are dyno-tested averages and may vary with hardware condition and fuel quality.
Measured by version
Versions of this model whose ECU and stock power match a dyno row exactly: the figure is the one measured on that engine, not a family average.
| Version | Engine | ECU | Stock | HP Gain | Torque Gain | Order |
|---|---|---|---|---|---|---|
| Ford Puma petrol | 1.5 ECOBOOST | MG1CS016 | 200 hp | +21 hp. 221 hp · +11% | +42 Nm | Order file → |
| Ford Puma diesel | 1.5 TDCI | MD1CS005 | 120 hp | +19 hp. 139 hp · +16% | +42 Nm | Order file → |
| Ford Puma petrol | 1.0 ECOBOOST BPF | MG1CS016 | 100 hp | +16 hp. 116 hp · +16% | +42 Nm | Order file → |
| Ford Puma petrol | 1.0 ECOBOOST BPF | MG1CS016 | 120 hp | +11 hp. 131 hp · +9% | +42 Nm | Order file → |
| Ford Puma petrol | 1.0 ECOBOOST BPF | MG1CS016 | 125 hp | +11 hp. 136 hp · +9% | +42 Nm | Order file → |
3 more versions of the Ford Puma are in our catalogue: we read their ECU and remap them, the dyno figure is not published yet. Upload your file. Order file →
Measured here, tunable everywhere
The Ford Puma engines listed above are the ones we have run on the dyno, so the figures on their pages are readings rather than software estimates. They are not the limit of what we tune: every ECU, engine and model we can read can be remapped for power, Ford Puma or otherwise. If your engine is not on this list, upload the original file anyway.
Every figure here was measured on this engine at a stock power your car has, sometimes on another car fitted with the same unit; the per-version table below marks only the exact matches.
ECU services available on Ford Puma
Solutions supported on the ECUs fitted to this model. Each engine page lists exactly which ones apply to its control units.
Frequently Asked Questions
Which Ford Puma engines can be remapped?
The 3 engines in the table above were measured on our dyno: 1.0 ECOBOOST BPF, 1.5 ECOBOOST and 1.5 TDCI. Other Ford Puma engines can be remapped too when we can read the ECU - the table is what we publish, not the limit of the service.
How much power does a Stage 1 add on a Ford Puma?
Between +11 and +21 hp depending on the engine; the best result measured is +21 hp on the 1.5 ECOBOOST. Every figure is a dyno reading on stock hardware, not an estimate.
Do I have to send the Ford Puma ECU?
No. Read the original file with your tool (KESS3, Autotuner, CMD, Dimsport, PCMTuner and others), upload it, and the tuned file comes back in 15-20 minutes to write into the car. Only the file travels.
Order your Ford Puma tuning file
Upload your original ECU file and receive a professional calibration in 15-20 minutes.
Tune Your File →v4.31.23